The monitor screen is selected by pressing the “View” button of the top panel’s monitor section, as well as the “View” button of the top panel’s talkback section. The screen controls various aspects of the console’s solo bus, control room outputs, and talkback section. The monitor/talkback screen contains the following separate tabs:
Monitor: This screen controls various solo options, dimming, speaker delay, and sources for the control room output.
Talkback A: This screen controls various adjustments for the talkback A path of console.
Talkback B: This screen controls various adjustments for the talkback B path of console.
Oscillator: This screen offers various controls for the onboard oscillator and how it is routed throughout the console.
Monitor/Talkback Screen: Monitor Tab:
The monitor tab controls various console options related to the solo bus, as well as the console’s control room outputs. These options include various solo settings, speaker dimming, speaker delay, and selection of sources for the control room output.
To adjust the various settings on the monitor tab, perform the following steps:
1. Adjust the 1st encoder to change the gain of the monitor signal. This digital gain stage occurs as a first preliminary level control, before the top panel’s analog-based monitor level control. A display above the encoder shows the currently set gain value in dB.
- A multi-segment level meter is displayed on the color screen to allow for proper gain staging of the monitor signal.
2. Adjust the 2nd encoder to scroll through the various solo methods available to the console when audio is routed to the solo bus. Available options include:
- Exclusive (Last): In this mode, pressing another solo button disengages the previous solo.
- Solo Follows Select: When this method is selected, the audio of the currently selected channel will automatically be sent to the solo bus. Since a user will often select a channel to adjust its dedicated DSP controls, this method is useful because the audio of the channel will now already be feeding the solo bus where it can be monitored with headphones in a live sound environment.
- Select Follows Solo: When this method is selected, any channel that is soloed will automatically become the currently selected channel.
- Channel Solo AFL: With this method, the channel and select button do not have any correlation to each other. When a channel’s solo button is pressed, its audio is sent to the solo bus in “after-fader listen” mode, reflecting the current level of the channel fader and any channel DSP that has been applied.
- Mix Bus AFL/PFL: This toggles the AFL/PFL setting for the mix buses when they are soloed (as opposed to the soloing of a single input channel).
- DCA Group AFL: This puts the contents of a soloed DCA group into after-fader listen mode when the solo button is pressed on a DCA channel.
- Use Master Fader: This allows the Main Fader/mute button to control the solo/mon output.
3. Tap the 2nd encoder to select and assign the currently chosen solo option.
4. Adjust the 3rd encoder to adjust the amount of digital delay that is applied to the control room signal path. The display on the screen will show the current amount of delay in feet, meters, and milliseconds.
5. Tap the 3rd encoder to toggle the delay function on/off.
TIP: The delay function is useful for aligning the sound of audio monitored through headphones or speakers used at the Front-of-House position with audio that is coming from the stage location.
By delaying the control room audio, it can be brought into alignment with the slightly delayed audio that has to travel from the stage to the Front of House position.
6. Adjust the 4th encoder to set the amount of volume reduction that occurs when the control room bus has its “dim” function enabled. The amount of volume reduction ranges from -40 dB to 0 dB (no change).
7. Tap the 4th encoder to toggle the dim function on/off.
8. Adjust the 5th encoder to adjust the volume trim for the source currently feeding the control room bus, allowing it to be level/matched with other sources. The amount of trim can be adjusted from -20 dB to +20 dB.
9. Tap the 5th encoder to toggle the control room between mono and stereo operation. This is very useful in a studio context for checking how a mix sounds when played back on a mono speaker such as a clock radio.
10. Adjust the 6th encoder to select what specific signal source to monitor in the control room bus. Choices include:
- Off (No source)
- LR Bus
- LR + C/M
- LR PFL (pre-fader listen solo bus)
- LR AFL (after-fader listen solo bus)
- Auxiliary returns 5/6
- Auxiliary returns 7/8
11. Tap the 6th encoder to activate the signal source that has been chosen.
Monitor/Talkback Screen: Talkback Tabs:
The talkback tabs offer various adjustments for the talkback paths of the console, such as destination of the talkback signal and more.
To adjust the various settings on the Talkback A tab, perform the following steps:
1. The screen displays a multi-segment level meter showing the signal strength of the talkback signal as it has currently been set. It also displays a multi-segment gain reduction meter, showing the user how much compression has been automatically applied to the talkback signal to keep its level even to the recipient.
2. Tap the 1st encoder to enable the talkback circuit. The internal/external talkback microphone will now transmit audio to the Talkback A path’s assigned destination.
3. Tap the 2nd encoder to switch the talkback circuit from the internal talkback to the external microphone connector. A 2nd tap of the encoder switches the console back to using the internal talkback microphone.
4. Adjust the 3rd encoder to set the gain of the talkback A signal. This is an additional gain stage that follows the initial gain stage set by the top panel Talk Level knob.
5. Tap the 3rd encoder to toggle on/off the talkback circuit’s “auto-dim” function. This function is useful in a studio setting, and will automatically dim the control room outputs when the talkback circuit is active. This prevents a feedback loop from occurring between the talkback microphone and the nearby studio monitors.
6. Adjust the 4th encoder to scroll through the various talkback destinations, which include:
- Mix Bus 1-16
- LR Bus
- Center/Mono Bus
7. Tap the 4th encoder to activate any talkback destination when it is currently selected. Multiple talkback destinations can be selected, allowing the talkback signal to reach many destinations at the same time.
8. Tap the 5th encoder to toggle the dedicated top-panel talkback buttons between latching and non-latching operation.
9. Adjust the 6th encoder to adjust the brightness of the lamp that is connected to the console’s top-panel lamp connector.
10. Tap the 6th encoder to toggle the attached lamp on/off.
All controls for the talkback B tab work as described above, but pertain to the talkback B signal path.
Monitor/Talkback Screen: Oscillator Tab:
The oscillator tab offers controls for the console’s onboard oscillator, a very handy tool that can be used for setting up PA systems and testing various signal flow paths without the need for a live source feeding a microphone. Settings include oscillator type, frequency, volume, and routing destinations.
To adjust the various settings on the Oscillator tab, perform the following steps:
1. Adjust the 1st encoder to set the level of the onboard oscillator.
2. Tap the 1st encoder to toggle the onboard oscillator on/off.
- The color screen displays a multi-segment level meter that show the current level of the oscillator.
3. Adjust the 2nd encoder to set the frequency of the primary onboard oscillator.
4. Adjust the 3rd encoder to set the frequency of the alternate onboard oscillator.
5. Tap the 3rd encoder to alternate between the 2 onboard oscillators.
6. Adjust the 4th encoder to select the type of oscillator to be used. Choices include:
- Sine Wave
- Pink Noise
- White Noise
7. Tap the 4th encoder to engage the selected oscillator type.
8. Adjust the 6th encoder to select a destination for the onboard oscillator. Choices include:
- Mix Bus 1-16
- Main L Bus
- Main R Bus
- Main L+R Bus
- Main Center/Mono
- Matrix Outputs 1-6
9. Tap the 6th encoder to assign the selected oscillator destination.